최신EMC Dell Networking Professional - DNDNS-200무료샘플문제
문제1
Refer to the exhibit. Based on the deployment diagram, which problem will the deployment engineer experience when trying to deploy this configuration?
Refer to the exhibit. Based on the deployment diagram, which problem will the deployment engineer experience when trying to deploy this configuration?
정답: A
문제2
Refer to the exhibits. A network engineer is troubleshooting an intermittent connectivity issue on a network.
The issue only occurs on VLANs 10 and 20.
Exhibit 1:
Exhibit 2:
Which configuration on the Z-Series is incorrect?
Refer to the exhibits. A network engineer is troubleshooting an intermittent connectivity issue on a network.
The issue only occurs on VLANs 10 and 20.
Exhibit 1:
Exhibit 2:
Which configuration on the Z-Series is incorrect?
정답: D
문제3
Refer to the exhibit. A customer installs a non-PoE line card to replace a previously installed PoE line card in slot 0. After unseating the line card, which two commands should a network engineer use to prepare the switch to accept the new line card?
Refer to the exhibit. A customer installs a non-PoE line card to replace a previously installed PoE line card in slot 0. After unseating the line card, which two commands should a network engineer use to prepare the switch to accept the new line card?
정답: C
문제4
A network engineer needs to create an IEEE 802.3ad Port-Channel between two S-Series switches using ports Tengigabit Ethernet 0/1 to Tengigabit Ethernet 0/4.
Which commands should be used to create the required port-channel?
A network engineer needs to create an IEEE 802.3ad Port-Channel between two S-Series switches using ports Tengigabit Ethernet 0/1 to Tengigabit Ethernet 0/4.
Which commands should be used to create the required port-channel?
정답: D
문제5
Refer to the exhibit.
A customer plans to deploy a two-tier OSPF ECMP Core in the configuration shown. All uplinks to the spine are 40Gbps. All uplinks to the leaves are 10Gbps.
What should be the oversubscription rate for the spine?
Refer to the exhibit.
A customer plans to deploy a two-tier OSPF ECMP Core in the configuration shown. All uplinks to the spine are 40Gbps. All uplinks to the leaves are 10Gbps.
What should be the oversubscription rate for the spine?
정답: B
문제6
On an N-Series switch, which three outputs display when a network engineer runs the command show system?
(Choose three.)
On an N-Series switch, which three outputs display when a network engineer runs the command show system?
(Choose three.)
정답: A,D,E
설명: (KoreaDumps 회원만 볼 수 있음)
문제7
Refer to the exhibits.
A network engineer has worked with PC support to install a new PC. After correctly configuring the PC's interfaces with valid IP addresses, the PC is not able to ping other devices on the 192.168.13.0/24 network.
The output from the PC after executing the command ipconfig /all is below:
The network engineer executes the command show mac address-table on the N-series switch to which the PC is connected.
The output of the show mac address-table command is below.
What are two reasons that the PC is unable to ping other devices? (Choose two.)
Refer to the exhibits.
A network engineer has worked with PC support to install a new PC. After correctly configuring the PC's interfaces with valid IP addresses, the PC is not able to ping other devices on the 192.168.13.0/24 network.
The output from the PC after executing the command ipconfig /all is below:
The network engineer executes the command show mac address-table on the N-series switch to which the PC is connected.
The output of the show mac address-table command is below.
What are two reasons that the PC is unable to ping other devices? (Choose two.)
정답: A,B
문제8
A network engineer is implementing MLAG using two N-Series switches, MLAG must be set up with 10 Gb ports and connecting to a single S-Series switch that will run 802.3ad to the MLAG Peers. The commands will be identical on the two N-Series switches. All ports on the N-Series switches are available to use. The VLAN that must be used is 10. The management interface on each N-Series switch has already been assigned an IP address.
Which set of commands should be used to meet the requirement for MLAG?
A network engineer is implementing MLAG using two N-Series switches, MLAG must be set up with 10 Gb ports and connecting to a single S-Series switch that will run 802.3ad to the MLAG Peers. The commands will be identical on the two N-Series switches. All ports on the N-Series switches are available to use. The VLAN that must be used is 10. The management interface on each N-Series switch has already been assigned an IP address.
Which set of commands should be used to meet the requirement for MLAG?
정답: A
설명: (KoreaDumps 회원만 볼 수 있음)
문제9
When facing the front of a C-Series switch, in which direction does air flow?
When facing the front of a C-Series switch, in which direction does air flow?
정답: B
설명: (KoreaDumps 회원만 볼 수 있음)
문제10
Refer to the exhibit.
The deployment engineer needs to use rapid PVST+ so that some traffic is forwarding on all inter-switch links on these three N-Series Switches. To do so, each switch has been set to the lowest spanning-tree priority value for one of the VLANs.
Given the labeled diagram shown, what Spanning-Tree Priority is Switch B advertising for VLAN 20?
Refer to the exhibit.
The deployment engineer needs to use rapid PVST+ so that some traffic is forwarding on all inter-switch links on these three N-Series Switches. To do so, each switch has been set to the lowest spanning-tree priority value for one of the VLANs.
Given the labeled diagram shown, what Spanning-Tree Priority is Switch B advertising for VLAN 20?
정답: B