시험 내용은 언제든 변경될 수 있습니다. KoreaDumps은 H12-261_V3.0 시험 변경이 확인되는 즉시 Huawei HCIE-Routing & Switching (Written) V3.0 연습문제를 업데이트하여 476문항의 최신성을 유지하고 있습니다.

Huawei H12-261_V3.0 시험 개요:

Huawei H12-261_V3.0 시험 요강 주제:

Huawei HCIE-Routing & Switching (Written) V3.0에 대해 알아야 할 모든 것

최신 Routing & Switching H12-261_V3.0 무료샘플문제

문제 #1

an engineer uses 2 router for IPv46 business test, by running BGP4+Simulate the interconnection between headquarters and branches. The network logical topology is shown in the figure, about the IPv6 between the two devices Route delivery, which of the following statements is false?

A. BGP4+ passUpdate Packets transmit routing information between peers
B. When routing, it will carry AS. _Path and other recognized mandatory attributes
C. likeUpdate NP is carried in the packet. REACHL NLRI Attribute, indicating that reachable routes are advertised
D. When routing is passed, Next_ Hop Attribute must be IPv46 Global Unicast Address

문제 #2

The router connects two EBGP neighbors through two parallel serial cables, what method would you use to achieve this through the two parallel serial cablesBidirectional load sharing between two connected EBGP neighbors?

A. To configure the EBGP neighbor relationship with the loopback interface as the update source, the IGP in each AS must have two equal-cost paths to the EBGP neighbor loopback interface address; and the command "next-hop-local"
B. Without any method, BGP will automatically realize the load balancing of traffic among different autonomous systems on the available links
C. To configure the EBGP neighbor relationship with the loopback interface as the update source, the IGP in each AS needs to introduce two equal-cost paths to the EBGP neighbor loopback interface address; and the command "ebgp-max- hop" and "next-hop-local*
D. Using the Loopback interface Establish EBGP neighbor relationship and configure EBGP Multi-hop, configure the loopback interface as the update source, and then use IGP to achieve equal-cost path load sharing between loopback addresses
E. Use the command "ebgp on both ends"-load-balance"

문제 #3

A network runs both ISIS and OSPF protocols. The topology is as shown in the figure.Route import is configured on RTB and RTC respectively, and the devices are connected through Gigabit Ethernet ports. The
2.2.2.2/32 network segment is imported on RTD through import-route. diThe rect method is introduced into OSPF, assuming all other configurations are defaults, what is wrong with the description of this network?

A. The next hop of the route that RTB learns from network segment 2.2.2.2/32 is RTA.
B. existThe following configuration is used on RTC to filter out only 2.2.2 when importing routesRoute
2/32 network segment. [RTC]ip ip-prefix 10 index 1 deny 2.0.0.0 8 less-equal 32
[RTC-isis- 1] filterr-policy ip-prefix 10 import
C. existAdjusting the ISIS priority on RTB to 160 can avoid suboptimal routing problems in the network.
D. The following configuration can beWhen RTC imports OSPF routes, the routes from the 2.2.2.2/32 network segment of RTD are filtered out. [RTC-acl-basic-2001]rule 5 deny source 2.0.0.0 0.255
255.255
[RTC-ac1-basi-2001]rule 10 permit
[RTC-isis-1]filter-policy 2001 import

문제 #4

Which of the following descriptions about MUX VLANs in Huawei switches is correct? (Single Choice)

A. MUX VLAN is divided into Principal VL AN and Subordinate VLAN is divided into Separate VLAN and lsolate VLAN
B. in the same VLAUnder N, MUX VLAN can and Super Mixed use of VLANs
C. each Separate VLAN can bind multiple Principals VLAN
D. Principal Port can and MUX All ports within the VLAN communicate

문제 #5

IGMP SSM Mapping statically binds the multicast source to the multicast group, so that the group members of IGMPv1 and IGMPv2 can also access the SSM multicast network. Which of the following statements about IGMP SSM Mapping is false?

A. Statically configure the mapping rules of SSM addresses on the IGMP querier, and map the group join information in the IGMPv1 or IGMPv2 member report to the group leave information
B. IGMP SSM Mapping does not process IGMPv3 report packets. In order to ensure that hosts running any version of IGMP on the same network segment can obtain SSM services, it is necessary to run IGMPV3 on the interface of the multicast router connected to the network segment where the member hosts are located.
C. If the IGMP SSM Mapping. function is not enabled, neither IGMPv1 nor IGMPv2 supports the deployment of multicast in SSM mode
D. The address of the multicast group of SSM is 232.0.0.0~232.255.255.255

질문과 대답: